Home & DIY

Wallpaper Calculator

Count the strips you need (wall width ÷ roll width), work out how many full-height strips each roll gives (allowing for trimming and pattern repeat), then divide. Walls 52 ft wide and 8 ft high, with 20.5-inch × 33 ft rolls and a 21-inch pattern repeat, need 29 strips at 3 strips per roll: 10 rolls.

ft
ft

For a whole room, total width = the room’s perimeter (for a 12 × 14 ft room: 12 + 14 + 12 + 14 = 52 ft).

in
ft

Use the size printed on your roll’s label. These values are examples.

in
in

Enter 0 for the repeat if the paper has no pattern to match (“random match”).

sq ft

Total area of large openings, e.g. a 3 × 7 ft door (21) + a 4 × 4 ft window (16) = 37.

Rolls to buy

—

—

Strips needed
—
Length of each cut strip
—
Full strips per roll
—
Wall area to cover
—

—

How to use the wallpaper calculator

  1. Measure the width of each wall you will paper and add them together. For a whole room, this is the perimeter.
  2. Measure the wall height from the top of the baseboard to the ceiling or crown molding.
  3. Enter the roll width and length and the pattern repeat from the label of the paper you plan to buy.
  4. Keep a trimming allowance, extra length at the top and bottom of each strip for cutting a clean edge.
  5. Optionally enter the area of large doors and windows.

Why the strip method beats square feet

It is tempting to divide the wall area by the area of a roll. But wallpaper is hung in full-height strips, and the leftover piece at the end of each roll is often too short to use. Pattern matching wastes even more. The strip method counts how many whole strips you can actually cut from each roll, so it gives a much more realistic number.

Wallpaper formulas

Strips needed = total wall width (in) ÷ roll width (in), rounded up Strip length = wall height + trimming allowance, rounded up to a whole number of pattern repeats Strips per roll = roll length ÷ strip length, rounded down Rolls = strips needed ÷ strips per roll, rounded up

Worked example: a 12 × 14 ft room

Perimeter 52 ft, walls 8 ft high. Rolls 20.5 inches wide and 33 ft long, with a 21-inch pattern repeat and 4 inches of trimming allowance. One door (3 × 7 ft) and one window (4 × 4 ft).

  1. Strips: 52 × 12 = 624 in ÷ 20.5 in = 30.4, round up to 31.
  2. Strip length: 96 + 4 = 100 in. With a 21-inch repeat: 100 ÷ 21 = 4.76, round up to 5 repeats = 105 in.
  3. Strips per roll: 33 × 12 = 396 in ÷ 105 = 3.77, round down to 3.
  4. Openings: 21 + 16 = 37 sq ft. One full strip covers 20.5 ÷ 12 × 8 ≈ 13.7 sq ft, so the openings replace 2 whole strips: 31 − 2 = 29 strips.
  5. Rolls: 29 ÷ 3 = 9.67, round up to 10 rolls.

Understanding pattern repeat and match

  • Random match: no pattern to line up (plain textures, stripes). Enter a repeat of 0. Least waste.
  • Straight match: the design lines up horizontally across every strip. Waste depends on the repeat length.
  • Drop (half-drop) match: the design lines up with every other strip, offset by half a repeat. It can use more paper than a straight match; some installers add extra on top of the calculated amount.

The repeat and match type are usually printed on the roll label or product page. The larger the repeat, the more paper is wasted on each strip.

Measuring tips

  • Measure each wall at its widest point and round up to the next inch.
  • Measure height in several places; older rooms are rarely perfectly level.
  • For a feature wall, enter just that wall’s width.
  • Sloped ceilings and stairwells need strips of different lengths. Measure the longest strip on those walls, or calculate them separately.

Before you buy

  • Check the batch number. Rolls from different print runs can differ slightly in shade. Buy all your rolls from the same batch.
  • Consider a spare roll for mistakes and future repairs, especially with expensive or hard-to-match designs.
  • Roll sizes vary. Different brands and countries use different widths and lengths, and some are sold as double rolls. Always calculate with the exact size of the product you choose.

Covering a floor instead? The tile calculator and square footage calculator handle flooring.

Frequently asked questions

How many rolls of wallpaper do I need?

Divide the total width of the walls by the roll width to get the number of strips, and work out how many full-height strips you can cut from one roll. Divide strips by strips per roll and round up. Using strips rather than square feet accounts for the offcuts at the end of each roll.

What is a pattern repeat?

It is the vertical distance before the design repeats. Each strip has to start at the same point in the pattern so the design lines up across seams, so strip lengths are rounded up to a whole number of repeats. Large repeats waste more paper. The repeat is printed on the roll label.

Should I subtract doors and windows?

Only large openings. You still need paper above and below windows and above doors, so the calculator only removes whole strips that an opening fully replaces. Many decorators simply ignore small windows to leave a margin for error.

Are all wallpaper rolls the same size?

No. Roll width and length vary by country, brand and product, and some rolls are sold as “double rolls”. Always use the width and length printed on the label of the paper you are buying.

Should I buy an extra roll?

It is often a good idea. Rolls from different production batches can vary slightly in color, so buying everything with the same batch number at once, plus a spare for mistakes or later repairs, avoids mismatches.